Thermostat Digital Dixxel( Spare-parts Walk in chiller-Freezer-Showcase)

Thermostat Digital Dixxel( Spare-parts Walk in chiller-Freezer-Showcase) dari Service Freezer Jakarta Indonesia"Cv.Jayco teknik mandiri"

Oleh: Service Freezer Jakarta Indonesia"Cv.Jayco teknik mandiri"  13/12/2011
Kata kunci: toko online, peluang usaha, belanja online

Thermostat Digital Dixxel( Spare-parts Walk in chiller-Freezer-Showcase)
Jayco Teknik Mandiri
Perbaikan Dan Pengadaan Spare parts Mesin Semua Jenis Mesin Pendingin Al:

Menyediakan Dan Pemasangan Kontrol Electrical Walk in-Chiller-Freezer-Showcase al:
-Thermostat Digital
-Timer Defrost-Paragon, dll
-Contactor Magnetic
-HLPS ( High Low Pressure Switch)
-OLPS ( Oil Pressure Switch)
-Selonoid Valve
-Oil Separator
Thermostat Digital Dixxel( Spare-parts Walk in chiller-Freezer-Showcase)
Tersedia Control Thermostat Digital DIXXEL
Spesifikasi Sebagai Berikut:
Display 3 digits, d.p., -
Power supply 12, 24Vac/ dc
110, 230Vac
Inputs
Probe NTC / PTC
Measurement
Measurement range probe dependent
Accuracy Better than 1% of full scale
Generals
Housing Self extinguishing ABS
Front protection IP65 with gasket
Display type red LED ( 13.2mm high)
Data Storage EEPROM memory
Operating temperature 0° ÷ 60° C
32° ÷ 140° F
Storage temperature -30° ÷ 85° C
22° ÷ 185° F
Relative humidity 20÷ 85%
Resolution 0.1° C or 1° F
Connection Screw-terminal block

SETTING DIXXEL CONTROL

Dixell Digital Controls
Many Oscartielle cases utilize an electronic control board with digital thermometer / thermostat, providing:
• Temperature accuracy.
• Programmable defrosting.
• Diagnostic capability ( eliminating need for mechanical defrost clocks) .
Please Note: These are Low Temp Control Setting Instructions for Oscartielle Gelato & Ice Cream Showcases
To Check Temperature Setting:
1. Press and hold in the set button for 5 seconds to see the temperature setting
2. To adjust the temperature setting use the up or down arrow
3. * * normal setting is 4 degree F
4. After checking or changing the temperature setting - press the set button
To Check All Parameters:
1. Press and hold in the down arrow and set
2. Button together for 5 seconds till you see HY – release both buttons
3. Press the down arrow 1 time till you see PR2
4. Press set and you will see PA5
5. Press set and you will see a flashing zero
6. Press the up arrow 3 times till you see 3
7. Press set and you will see the 2nd flashing zero
8. Press the up arrow 2 times till you see 2
9. Press set and you will see the 3rd flashing zero
10. Press the up arrow 1 time till you see 1
11. Press set
You Will Now See HY:
1. Press set and you will see the setting for HY
2. To change a setting use up or down arrow
3. Press set and you will see the next parameter
4. Then press set to check that setting
5. continue to press set one time to move to next parameter
6. And then set again to check that parameter
From HY:
If you just want to check a certain parameter, use the up or down arrow till you see the one you want to check. Then press set to check that parameter.
After checking or changing the parameters – wait for 10 to 15 seconds and the control will reset and go back to reading the case temperature.
Label Parameter Description Range Value Menu
Set Set point LS ÷ US 4 ---
Hy Hysteresis 0.1 ÷ 25.5 ° C / 1 ÷ 45 ° F 3 Pr1*
LS Minimum Setpoint -50.0° C ÷ SET / -58° F ÷ SET -22 Pr2
uS Maximum Setpoint SET ÷ 110° C / SET ÷ 230° F 80 Pr2
odS Outputs activation delay at startup 0 ÷ 255 min. 0 Pr2
Ac Anti-short cycle delay 0 ÷ 30 min. 1 Pr1^
con solenoid valve on time with faulty probe 0 ÷ 255 min. 15 Pr2
coF solenoid valve off time with faulty probe 0 ÷ 255 min. 30 Pr2
cH Governor type of action cL / Ht cL Pr2
cF Temperature measurement unit: Celsius, Fahrenheit ° C / ° F ° F Pr2
rES Resolution ( integer/ decimal point) in / de In Pr2
Lod Local display P1 / P2 / P3> P1 Pr2
tdF Defrost type rE / in in Pr2
EdF Defrost mode rtc / in / Sd In Pr2
SdF Set point for SMART DEFROST -30 ÷ + 30 ° C / -22 ÷ + 86° F 0 Pr2
dtE Defrost termination temperature -50.0 ÷ 110.0 ° C / -58 ÷ 230 ° F 45 Pr1^
idF Interval between defrost cycles 1 ÷ 120 ore 6 Pr1^
MdF ( Maximum) length for defrost 0 ÷ 255 min. 15 Pr2
dFd Displaying during defrost rt / it / SEt / dEF / dEG rt Pr2
dAd Max display delay after defrost 0 ÷ 255 min. 0 Pr2
Fdt Draining time 0 ÷ 255 min. 5 Pr2
dPo First defrost after start up no / Yes n Pr2
dEM End defrosting global mode ALL / Loc Loc Pr2
Fnc Fans operating mode C-n/ c-y/ O-n/ O-y O-n Pr2
Fnd Fans delay after defrost 0 – 255 min. 1 Pr2
Fst Fans stop temperature 120 Pr2
ALc Temperature alarms configuration: relative/ absolute rE / Ab Ab Pr2
ALu Maximum temperature alarm -50.0 ÷ 110.0 ° C / -58 ÷ 230 ° F 170 Pr2
ALL Minimum temperature alarm -50.0 ÷ 110.0 ° C / -58 ÷ 230 ° F -40 Pr2
AFH Temperature alarm and fan hysteresis 0.1 ÷ 25.5 ° C / 1 ÷ 45 ° F 2 Pr2
ALd Temperature alarm delay 0 ÷ 255 min. 15 Pr2
dAo Delay of temperature alarm at start up 0 ÷ 23h 50 min. 1.3 Pr2
EdA Alarm delay at the end of defrost 0 ÷ 255 min. 30 Pr2
dot Alarm delay after closing of the door 0 ÷ 255 min. 30 Pr2
ot Thermostat probe calibration -12.0 ÷ + 12.0 ° C / -21 ÷ 21° F 0 Pr1*
Untuk Informasih Lebih Lanjut
Thermostat Digital Dixxel( Spare-parts Walk in chiller-Freezer-Showcase)
Hubungi
021-8896324
021-70031189
021-70413070
081383577023

Kata kunci: AC, belanja online, Coldstorage Service, Freezer Service, Jasa penyedia peralatan penyejuk udara, Jasa perbaikan alat penyejuk udara, peluang usaha, Peralatan penyejuk udara, Service Chiller Jakarta, toko online,

Kontak Service Freezer Jakarta Indonesia"Cv.Jayco teknik mandiri"

Email

Mencetak halaman ini

Memberikan